The Radium Engineering fuel pump hanger allows the use of 1 or 2 aftermarket pumps in the stock Mitsubishi Evo X fuel tank. The machined assembly drops-in the factory fuel tank using the OEM hold-down flange. A single 8AN male pump feed port and 6AN male return port simplify aftermarket -AN hose plumbing. Electrical hardware is included for the fuel pump power, OEM level sender, and OEM temperature sensor.



One major issues with the OEM EVO X fuel pump hanger is the restrictive return port and venturi jet pump. When using aftermarket high-flow fuel pumps, the OEM jet pump becomes too restrictive creating unwanted backpressure in the regulator return line causing excessive fuel rail pressure. The Radium fuel pump hanger includes Radium's own proprietary venturi jet pump with interchangeable orifices to minimize back pressure.



The kit also includes a 2-piece anodized aluminium collector box that sits at the bottom of the OEM fuel tank. This container is NOT a total solution to fuel starvation, but does improve the fuel supply around the pump(s) inlet. There are two 1" ball check valves incorporated on the front and rear of the box that serves as trap doors keeping the pump(s) supplied with fuel during aggressive driving. Furthermore, all returning fuel from the pressure regulator return and the crossover hose enter the collector box keeping it full. The collector box also permits a mounting solution for the OEM fuel level and fuel temperature sensors. Also included are 2 mating connectors for the sensors making the kit easily serviceable.



Single pump applications can reuse the OEM fuel pump controller wiring, but it is recommended to upgrade the OEM wiring as high flow fuel pumps draw additional current requiring larger gauge wire. Fuel pump wiring kits can be purchased HERE. Select qty1 for single pump applications and qty2 for dual pump applications.

Features - Anodized Aluminum Mounting Plate
- Anodized Aluminum Collector Box and Check Valves
- Anodized Aluminum Venturi Jet Pump with Multiple Orifices
- Anodized Aluminum 8AN Male Pump Outlet Fitting
- Anodized Aluminum 6AN Male FPR Inlet Fitting
- Anodized Aluminum Fuel Level and Temp Sensor Bracket
- Anodized Aluminum Dual Pump Cradle
- Electrical Hardware for Fuel Pumps and OEM Sensors
- Fluorosilicone Duckbill Return Valve
- Submersible Rubber Fuel Hose
- Stainless Steel Hardware and Clamps

Pump Configuration Selection
This kit is available with or without fuel pumps included. If you are going to use your own pumps or source pumps elsewhere, select the option "Single / Dual Hanger, Pumps Not Included" from the drop down. Note that there will be enough components included with this option to use 1 or 2 fuel pumps. Depending on the setup, some parts will simply not be used. Note: The pump wiring harness is always configured to use up to 2 pumps even if only 1 pump is selected.

Next, select the type of pumps that will be used so the appropriate internal wiring connectors will be included in the kit. If pumps are needed, the kit will come preassembled and 65 micron sock filters will be installed on all fuel pumps.

This kit eliminates the OEM hanger's "post" fuel pump filter. A low micron aftermarket fuel filter should be installed downstream to protect the injectors from debris. NOTE: the optional fuel feed kits listed below include a post pump filter.

Options
20-0246-XX FUEL HANGER FEED, EVO X
The feed kits include everything required to connect directly to an aftermarket (-8AN male) fuel rail for both single and dual pump configurations. PTFE -8AN hoses attach to a Radium Engineering fuel filter that mounts underneath the vehicle using a specifically designed EVOX bolt-on bracket. Depending on the kit selected (-01,-02,-03), the fuel filter will be assembled with 1 of 3 different elements.



INCLUDES
- Radium Engineering Filter (-01 Cellulose, -02 Microglass, or -03 Stainless)
- Radium Engineering 8AN Adapter Fittings (x2)
- Radium Engineering 2-Piece 60mm Filter Clamp
- Radium Engineering Aluminum EVOX Filter Bracket
- 8AN PTFE Fuel Feed Hose Replacement (x2)
- Stainless Steel and Aluminum Hardware



-20-0249 FUEL HANGER RETURN, EVO X
The return kit provides all of the necessay hose, fittings, and hardware to convert the OEM Evo X fuel feed line to be used as the return line. This is a method to replace the restrictive 1/4"(6.5mm) OEM return hose. In the engine bay, the -6AN PTFE return hose will attach directly to a Radium DMR if mounted in the top port of a Radium fuel rail. The two SAE quick connect fittings allow each end of the OEM feed line to be connected in an easy, leak-free manner to the rest of the kit.



INCLUDES:
- 6AN PTFE Hose Replacement
- SAE Quick Disconnect Male Fittings (x2)
- Stainless Steel Cushion Clamp



For Evo Model X Only. Please select options from the drop down menu on the right.

Stock images used. Actual product may vary.