OPEN AS USUAL! - SumoPower remains open & is available on getting your orders shipped! - Our website shows LIVE STOCK LEVELS with up-to-date information! - Our phone lines & Contact E-Mails are available for your needs and requests! Please note that there may be a slight delay in getting back to you due higher demands!

Radium: Catch Can Kit - Honda S2000 (00-05)

Radium: Catch Can Kit - Honda S2000 (00-05)
Radium: Catch Can Kit - Honda S2000 (00-05)
Radium: Catch Can Kit - Honda S2000 (00-05)
Radium: Catch Can Kit - Honda S2000 (00-05)

Radium: Catch Can Kit - Honda S2000 (00-05)

No items available to display


Ships in 1 week

Radium: Catch Can Petcock Drain Kit - 20-0024 ( + £31.85 )

This installation kit was specifically designed for the 00-05 Honda S2000 LHD chassis. It is not compatible with any RHD or 06-09 LHD S2000 models.

An oil catch can is essential on a performance vehicle to protect the engine from elevated levels of crankcase blow-by accumulated from aggressive driving. Excess oil-saturated air circulating back into the air intake stream can lead to degraded performance.

Features:

-Effectively raises the octane and increased engine performance from cleaner inlet air
-Prevents oil buildup in the intake or intercooler system walls, throttle body, intake manifold, etc.
-Excessive oil collection can be an indicator of a damaged engine.
-Lowers hydrocarbon emissions
-Capacity: 6 fluid ounces
-Height (without fittings): 5 inches
-Outside Diameter: 2.45 inches

S2000 CATCH CAN KIT OPTIONS



Radium Engineering offers two completely independent S2000 oil catch can kits that are sold individually or together. They do NOT vent to atmosphere (VTA), thus are emissions and track legal. Closed loop systems route clean filtered air back in through the engine to be burned and to promote negative crankcase pressure for optimal performance. Furthermore, closed systems prevent unwanted oil vapors into the cabin.

The "crankcase vent" catch can kit (shown below) runs inline with the 1/2" valve cover breather port. At low loads it experiences atmospheric pressure, but when the engine is at high load (WOT), this hose will experience vacuum and would normally be drawing unwanted crankcase vapors, unspent fuel, and oil sludge into the air filter intake pipe. If the engine is turbocharged or supercharged and you are finding oil accumulation stuck in the intercooler, this catch can is a necessity as oil will lower the thermal efficiency properties of the heat exchange process.

photo catchcan1_zpszvabsscu.jpg

The "PCV" catch can kit (shown below) runs inline with the 3/8" PCV (positive crankcase ventilation) valve. When the intake manifold pressure is close to or greater than atmospheric pressure, the PCV "check" valve closes and, thus, this hose experiences no flow. Conversely, the PCV hose will experience "metered" vacuum when the engine is idling, steady state cruising, and decelerating. This would normally draw unwanted crankcase vapor, unspent fuel, and oil sludge into the intake manifold immediately after a high load run. Note: Because the Radium catch cans are pressure sealed, they are great for boosted applications as well so connecting to the intake manifold is permitted.

photo catchcan2_zpssbjisypo.jpg

For the ultimate in engine protection, Radium recommends the S2000 "dual catch can kit" (shown below) which utilizes both the "crankcase vent" catch can (foreground) and "PCV" catch can (background).

photo catchcan3_zpssi3ja4qa.jpg

Crankcase Vent Kit Includes:
-Radium billet oil catch can with integrated condenser and dipstick
-Radium laser cut powder coated S2000 specific mounting bracket
-Anodized aluminum -8AN hose ends and adapter fittings
-Enough 1/2" PCV rubber hose to mate to custom applications
-Vacuum and heater hose to eliminate OEM metal hard tube loom
-Stainless steel mounting hardware

photo catchcan4_zpsdpv3jyq6.jpg

PCV Kit Includes:
-Radium billet oil catch can with integrated condenser and dipstick
-Radium laser cut powder coated S2000 specific mounting bracket
-Anodized aluminum -6AN hose ends
-Anodized -6AN adapter fittings
-Stainless steel mounting hardware
-Honda OEM spring hose clamps
-3/8" PCV rubber hose

photo catchcan5_zpsw0ec40io.jpg

PETCOCK DRAIN KIT OPTION

-Anodized -4AN O-ring barbed fitting
-Nylon ¼” barb mini ball valve
-6ft high temperature rated 1/4" rubber hose

This kit, sold seperately, can be used to remotely drain the catch cans without the need to unscrew the canister body.

photo catchcan6_zpsehnanaur.jpg

For Honda S2000 (06-09) Model Only.

Stock images used. Actual product may vary.

We have placed cookies on your device to help make this website better.

Ok