Please select from the mounting hardware options on the right. If no mounting hardware is required, please leave options unchecked

RADIUM DOES NOT OFFER A WARRANTY ON ANY FUEL PUMPS! FUEL PUMPS CAN BE RETURNED IN UNUSED CONDITION WITHIN 30 DAYS OF PURCHASE. SEE TERMS AND CONDITIONS FOR MORE INFORMATION.

A fuel surge tank (FST) is designed to prevent fuel starvation to the engine on vehicles with inadequate fuel tank baffling. The FST fuel pump(s) directly feed the fuel rail(s). The volume of fuel inside the surge tank acts as a buffer to always keep the FST pump supplied with fuel. This volume is maintained by the main fuel tank's pump as well as the fuel returning from the fuel pressure regulator. Excess fuel in the surge tank is returned back to the vehicle's main fuel tank.

The surge tank also provides a quick and easy way to upgrade any standard fuel system without the need to modify the stock fuel tank or pump. This is an excellent fueling solution for vehicles installing large fuel demand power upgrades such as forced induction.

All Fuel Surge Tanks Include:

- Extruded and Machined Aluminium 1.5 Litre Canister.
- Bright Dipped Anodized and Laser Engraved Housing.
- Removable O-Ring Sealed Billet Aluminium Caps.
- 6AN Male Feed and Return O-Ring Port Fittings.
- Nickel Plated Electrical Connector with 24" Flying Leads.
- Corrosive Resistant Stainless Steel Hardware.
- Extra O-rings For Servicing.

All pumps mount internally using gasoline, ethanol, and methanol resistant wiring. For dual-pump configurations, each pump is wired independently. All hoses are submersible and E85 safe. The pump outlet fitting(s) are available in -6AN male size only (shown in green). The other ports can be adapted to other -AN sizes using adapters (sold separately).

How to Select Your Fuel Surge Tank Configuration:

Determine if your application will require one or two pumps. This is based on determining how much fuel flow the engine will need. Next, decide if the pump(s) will be purchased through Radium Engineering (pump included) or elsewhere (pump not included). Use the drop-down menu to make your selection. NOTE: When pump(s) are included, the FST comes fully asssembled and is ready to be installed in the vehicle. When purchasing without pumps, use the included instructions and/or this video HERE to aid in the assembly. Next, select the fuel pump model that will be used from the options shown. If you are unsure which pump will be best for the application, CLICK HERE for an unbiased performance test of some of the fuel pumps we offer. CLICK HERE for a easy to read side-by-side comparison of all the fuel pumps we offer.

Walbro GSS342 255LPH Pump:

This FST can be configured for single or dual pumps. For a triple pump FST using these pumps, please go to the Radium Multipump FST page. Shown below is the top view of the single pump variation.



Walbro F90000262 Gas Pump:

This surge tank comes in a single pump version only. Please check out the Radium Multipump FST if more than 1 pump is required. Shown below is the internal structure of this surge tank (shown without the canister).



Walbro F90000267 E85 Pump:

This surge tank comes in a single pump version only. Please check out the Radium Multipump FST if more than 1 pump is required. Shown below is the internal structure of this surge tank (shown without the canister).



AEM 50-1000 Gas Pump:

This FST can be configured for single or dual pumps. For a triple pump FST using these pumps, please go to the Radium Multipump FST page. Shown below is the dual pump variation.



AEM 50-1200 E85 Pump:

This FST can be configured for single or dual pumps. For a triple pump FST using these pumps, please go to the Radium Multipump FST page. Shown below is the single pump variation.



Bosch 0 580 254 044 Pump:

This surge tank comes in a single pump version only. To purchase the Bosch 0 580 254 044 Fuel Pump, go HERE. Please check out the Radium Dual Bosch FSTs if more than one Bosch fuel pump is required.



Mounting Hardware:

The fuel surge tank can be mounted anywhere in the vehicle. However, mounting near collision prone areas, heat sources, or moving parts such as suspension components should be avoided. Note: All of the single pump FSTs listed above can be mounted anywhere from vertical to horizontal. However, the dual pump FSTs cannot be mounted completely horizontal because the pickups are on opposing sides of one another internally. Choose a bracket below that best fits the application.



Floor and Wall Mount: This bracket is laser cut from aluminium and powder coated black and can be mounted on the side or bottom of the surge tank.

Frame Mount: Because this bracket has a 90deg formed bend and is cantilevered, it is constructed from steel for superior strength. It is not only nickel plated to resist corrosion, it also allows for components to be grounded to the spare hole in the bracket. This assumes the bracket is mounted to an electrically conductive material such as a steel frame.

Angled Mount: This mounting bracket is used for vehicles that may have a limited mounting height. It can be mounted on a floor and against a wall. This bracket is made from laser cut aluminium and powder coated black.

Mounting options: http://data.radiumauto.com/PublicDocs/FST_DIMENSIONS.PDF

Installation Instructions, Bosch 044 and Walbro F90000262 Gas and F90000267 E85 equipped standard FSTs: http://data.radiumauto.com/PublicDocs/19-0040BOSCH.PDF

Installation Instructions for all other standard FSTs: http://data.radiumauto.com/PublicDocs/19-0040.PDF

Universal product for all Evo Models.

Stock images used. Actual product may vary.